This wiki was updated to MediaWiki 1.37. If you notice any issues, please report them to admin[at]opensuse.org

HCL Talk:Jetson Nano

Jump to: navigation, search

[0009.640] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0009.646] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0009.659] Updated bootarg info to DTB [0009.663] Adding uuid 000000016450b7000c00000005fb8400 to DT [0009.668] Adding eks info 0 to DT [0009.674] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0009.680] Updated memory info to DTB [0009.688] set vdd_core voltage to 1125 mv [0009.692] setting 'vdd-core' regulator to 1125000 micro volts [0009.697] Found secure-pmc; disable BPMP


U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700)

SoC: tegra210 Model: NVIDIA Jetson Nano 2GB Developer Kit Board: NVIDIA P3541-0000 DRAM: 2 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB

      • Warning - bad CRC, using default environment

In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 MMC: no card present starting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 126464 Firmware timestamp: 0x5f23e558, Version: 50.26 release

Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... 4 USB Device(s) found

      scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device

Warning: eth_rtl8169 using MAC address from ROM BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 BOOTP broadcast 8 BOOTP broadcast 9 BOOTP broadcast 10 BOOTP broadcast 11 BOOTP broadcast 12 BOOTP broadcast 13 BOOTP broadcast 14 BOOTP broadcast 15 BOOTP broadcast 16 BOOTP broadcast 17

Retry time exceeded; starting again missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/01-48-b0-2d-2e-90-4f

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/000

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/00

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/0

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-tegra210-p3541-0000

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-tegra210

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm

      • ERROR: `serverip' not set

missing environment variable: bootfile Retrieving file: pxelinux.cfg/default

      • ERROR: `serverip' not set

Config file not found